Electrical engineering

CIRCUIT RACE Date:- 01/03/2019 Time:-11:00am-02:00pm

This is an event based on problem solving of electrical circuits

RULES:

  • Student should participate individually.
  • Interested candidates should register themselves online.
  • Individual ID will be provided during the event.
  • Decision of event organiser will be treated as final.
  • Participants should report at the venue in their respective slots. No requestwill be entertained later on regarding this.
  • The organiser will not take any responsibility for losing any belongings of the participants.
  • EVENT PROCEDURE:
  • Round 1: Participants will have to reach the final point by solving 3 individual questions placed at 3 different positions.The maximum time allotted for this round is 20 minutes.
  • Round 2: The procedure will be same as round 1 but the question will be difficult as compared to the previous round. Maximum time allotted for this round is 25 minutes.

N.B[ Winner will be selected based on the accuracy and the time taken to reach the final point]

SIMULATION DATE:- 01/03/2019 TIME:-2:00PM-5:00PM ​

This is an event based on electric circuit simulation,circuit implementation,and application of power system,control system,circuit theory,electronics etc.

Rules:

  • Maximum participants is two per team for 1st and 2nd
  • Each team must register themselves online.
  • Team ID will be provided during the event which will be mentioned in rough page as well as on the computer.
  • Decision of the event organizer shall be treated as final.
  • Participants should report at the venue in their respective slots. No request will be entertained later on regarding this.
  • The organizer will have no responsibility for loss of any belongings of the participants.
  • All simulation result should be saved in a folder at desktop after completing simulation with a title of team ID
  • In case of power failure extra time will be given as per requirement.

EVENT PROCEDURE:

Round one:-

Team participating in this round will be handed over with a question paper consisting of simple circuit.Participants have to simulate this circuit and show their outputs on computer and on given paper.

Round two:-

Participants will be handed over application oriented problem which will  to be solved Using given software(Pspice,Proteus,PSIM,MATLAB).

DETECT MY FAULT Date:- 02/03/2019 Time:-10:00am-01:00pm

This is an event based on fault detection in electrical wiring, lighting circuit, connection of equipments and some small electronics circuit also.

Rules:

  • Each participating team must consist of two members for all rounds.
  • Each team must register them self online before commissioning of this event.
  • Team ID will be provided during the event which will be mentioned in the given page as well as on the faulty system.
  • Decision of the event organizersis considered as the final decision.
  • Participants should report on or before 30 min in their respective rooms. No request will be entertained later on regarding this.
  • The organizer will have no responsibility for loss of any belongings of the participants.
  • No one can use their cell phones or any electronic gadgets during the event.
  • For any further queries contact to student coordinator.

EVENT PROCEDURE:

Round one:-

Participating teams in this round will be handed over simple faulty circuit. Participants have to find out the faults and write it on the given page. The selection of the round will be done on the basis of accuracy and time taken to find the fault.

Round two:-

Participating teams will get an electronic faulty circuit. Participants have to find out the faults as well as they have to make the necessary corrections. Selection from this round will be based on correctness of the circuit. If two or more team coincide then time taken to complete the circuit will be considered for the selection.

Final round:-

Participating teams will get a complex faulty electronic circuit. At first they have to find out the required components to complete the given circuit. After that they will be provided with the required components. Then they have to complete the whole circuit. If any team calls for wrong components there will be some negative points.

System Design Date:- 02/03/2019 Time:-1:00Pm-4:00Pm

Electrical Design entails planning, creating, testing or supervising the development and installation of electrical equipment interpret the electrical engineering drawing

 

Rules:

  • Student should participate individually.
  • Each participants should register themselves online.
  • Individual ID will be provided to each Participants during the event which will be mentioned in paper as well as on the computer.
  • Decision of the event organizer will be treated as final.
  • Participants should report at the venue in their respective slots. No request will be entertained later on regarding this.
  • The organizer will have no responsibility for loss of any belongings of the participants.
  • In case of power failure extra time will be given as per requirement.

 

EVENT PROCEDURE:

Round one:-

MCQ based 50 question will be given based on concept of electrical system design which includes electrical wiring,IE rule ,service connection,designing of lighting circuit,etc.

Time allotted for this round is 30munites.

Round two:-

The electrical design based problem will be given to the participants. They will have to design the system in given paper or in“Autocad” within 50munites.They should also estimate about the design within the proper time.